Description
Leading the way with the industry's first PREMIUM Plug and Play. Assembly usually takes less time than unwrapping. High Quality motor/esc/prop/spinner/servos/arms/extensions ALL PREINSTALLED, TESTED AND PROGRAMMED FROM THE FACTORY. Rigorously tested for the best results. After an easy assembly just install your receiver, battery, a quick throttle calibration and you're ready to go!
- Advanced construction for today's demanding pilots
- Factory assembled detailed canopy interior
- Pre-baffled cowling for maximum motor cooling
- Incredible value with carbon fiber wing tube, landing gear and tailwheel assembly.
- Complimentary wing bag included
- Featuring Skywing's PATENTED rapid assembly wing design and easy servo connections
Specs:Wingspan: 60 in.Length: 61 in.Weight: approx 6lb depending on batteryNeutral center of gravity - center of tube (marked inside)Motor - Skywing/Dualsky GA1500RESC - Skywing/Hobbywing Platinum 100 V3 ESC, BEC preprogrammed at 7.4VServos - Skywing/Theta SW988HV servos x 4Propeller - 16x7 wood and 16x8 poly (both included)Spinner - 63mm
Recommended High Rate ThrowsAilerons - 38 deg up, 37 deg downElevator - 50-55 degrees up and downRudder - 50-55 degrees each direction
RequiresFull range - 5+ channel transimetterFull range - 5+ channel receiver6s 3300-4000mah LiPo batterybasic hand tools and adhesives
Basic Assembly:1. Carefully unwrap and inspect all contents, make sure you don't discard any important parts.2. Use low temp covering iron (and covering heat gun if necessary) to ensure all covering and trim pieces are tight and secure3. Use blue/medium thread lock to install landing gear with included bolts. Double check wheels spin freely.4. Carefully slide elevator/stab set all the way forward. Ensure it is seated completely before carefully gluing in place with thin CA.5. Slide rudder hinges in place and ensure minimum gap/full throw without binding and when satisfied secure each hinge with thin CA.6. Center the rudder and elevator servos electronically then attach servo arms as close to perpendicular to the servo case. Minor subtrim may be necessary but when satisfied secure the center screw and pinch bolt with a drop of blue/medium thread lock.7. Install wing tube then slide wings in place. Make sure the wing locks are UP to accept the stud at the wing root and once seated completely slide locks DOWN to secure.9. Attach SFG's/wing tips if you prefer a more stable aircraft at low speeds and high alpha. Loosen bolts at the wing tip, slide SFG/wing tip over and back then tighten thumb bolts. IT IS NOT NECESSARY TO OVERTIGHTEN THESE BOLTS10. Ensure receiver is secure, battery is charged and secured at the correct location for the CG you prefer, install the canopy and ensure the spring latch is seated.
* It is HIGHLY recommended to use the included plug in capacitor as some radio/receiver systems are sensitive to spikes in voltage *
Product Information
1) Advanced construction for today's demanding pilots
2) Factory assembled detailed canopy interior
3) Pre-baffled cowling for maximum motor cooling
4) Fast assembly time with pre-hinged and pre-sealed ailerons and elevators
5) preinstalled high quality extensions.
6) Incredible value with carbon fiber wing tube, landing gear and tailwheel assembly.
7) Wing bag and electric spinner - INCLUDED
8) Skwying's PATENTED rapid assembly wing design!
PRODUCT DATA
Wingspan
60 in./1524mm
Lenqth
61vin./1552mm
Wing Area
731.6 sq in/47.2dm²
Weight
6.4lbs/2.9kg
Packaging Size/ Weight
134*49*27cm/7kg
Test device:
Motor:dualsky GA1500R
ESC:Hobbywing Platinum 100A V3
Servos:THETE THM988
Propellor:16*8
power supply:6S/3300-3700mah
servo arm:Elevator=1.25" *2 Aileron=1.25" *2 Rudder=1" *1
Test device:
Motor dualsky: GA1500R
ESC Hobbywing Platinum: 100A V3
Servos thete: THM988 HV
Propellor: 16*8
power supply: 6S/3300-3700mah
spinner: 2.5"63mm
servo Arms: Elevator=1" *1 Aileron =1.25" *2 , Rudder=1" *1
REQUIRED:
1) Brushless motor*1pcs
2) Carbon Propeller (16X8)*1pcs
3) 90A-120A ESC *1pcs
4) Digital High Torque Metal Gear Servos 35*15mm/10kg*4pcs
5) 1"-1.25" Arms - tapped for 2mm hardware (ailerons 1"x 2, elevator 1.25"x 1 rudder 1.25" x 1)
6) 6s 3000-4000mah LiPo battery*1
HD Arm Options
Lightweight Servo Arms-1.25"(x 4)25T-MKS,Savox-BLUE
Lightweight Servo Arms-1.25"(x 4)25T-MKS,Savox-RED
Lightweight Servo Arms-1.25"(x4)25T-MKS,Savox-SILVER
Features
1.No need for any programming of the device
2.ESC default output voltage is 7.4V, supports 6.0-8.4V voltage speed regulation
3.ESC has welded XT90 power connector
4.The ESC design of the all-aluminum shell helps to dissipate heat better!
The combined contents are as follows:
Motor;dualsky/ga1500r(v2?-KV540=1pcs
ESC: skywing/hobbywing platinum 100A-V3(V2)=1pcs
Servo:skywing/Theta sw988=4pcs
pro-1?skywing Wood-Painted/16*7=1pcs
pro-2?sunnysky Plastic material /16*8=1pcs
Arms; skywing/1.0"-M2 =2pcs (Aileron?
Arms; skywing/1.25"-M2 =2pcs (Elevator / Rudder?
The recommended battery capacity is 6S 3300-3700mah
Product details photo
Appreciation of static pictures
Reviews
There are no reviews yet.